Home > Power Supply > Repairing Or Replacing Bad Auxiliary 12-v Atx Connector

Repairing Or Replacing Bad Auxiliary 12-v Atx Connector

Contents

However, I've decided to simply purchase a low-end slot-powered graphics card instead. Instant download of the PDF eBook edition for $9.95 Computer Repair with Diagnostic Flowcharts Power Supply Video Card Motherboard/CPU/RAM Hard Drives CD and DVD Sound Card Modems and Networks Starting Your The back of the expansion card forms a bracket that resembles a slot cover and is secured to the chassis in the same way. If you have a single high speed video card slot, whether PCI Express or the older AGP technology, it could be that slot is faulty. http://diskpocalypse.com/power-supply/need-help-again-purpose-of-alternate-power-connector.php

These sections describe the common tasks involved in working on a PC things like opening the case, setting jumpers, manipulating cables, and adding or removing expansion cards. Figure 2-12: Five white PCI slots and a dark brown AGP slot Figure 2-13: Two white PCI slots, two PCI Express X1 slots, two more white PCI slots, and a black Periodic power cycling, tweet-tweet, flub-flub, blinking power light - shorted semiconductors, faulty over voltage or over current sensing components, bad controller. In all cases, bad solder connections are a possibility How can you tell whether a power supply meets minimum safety standards?

P2 Connector On Power Supply

It sounds like creating this power connector is not an option for the average person. There are lots of wire coils, capacitors, and other components inside the power supply that do the work, and during the conversion process, a great deal of heat is produced. Analog multimeters, or non-autoranging digital meters, must be set manually to the correct range and can be damaged more easily by overvoltage. In the old days, SMPS controllers were designed with discrete components.

Warning!I have seen and heard that powering up a system with only the motherboard connected may not provide enough load on the PSU and can cause it to fail. If this doesn't work, you'll now have to locate the problem component through the process of elimination. Notable characteristics of LPSs are excellent regulation and low output ripple and noise. P5 Connector Power Supply Solder one end of the appropriate size resistor (for your application) along with the indicator circuit (if desired) to a well insulated clip lead about 2-3 feet long.

In particular, read carefully any instructions about installing software drivers for the card. Big manufacturers don't want this bill passed. Fortunately, the cable that came with the motherboard fit both the motherboard and the drive connectors properly, allowing us to complete the installation. https://www.ifixit.com/Wiki/General_Computer_Repair_Procedures MONITOR YOUR MOTHERBOARD To protect your system against thermal problems, we recommend installing and activating the monitoring utility supplied with the motherboard.

With the exception of a few low-end video cards, almost all video cards use active heat sinks to blow hot air away from the GPU. Atx 20-pin Connector When you press the system power switch, the motherboard signals the power supply to provide power. Figure 4-1. The power transformer also provides the isolation between the load and the line.

P4 Connector

Return to Diagnostic Chart Since the PC powered up with nothing but the hard drive connected, the power supply is probably good and there is either an excessive current draw or http://electronics.stackexchange.com/questions/33190/how-can-i-power-my-6-pin-pci-express-card-without-using-an-atx-power-supply Don't assume your problem is complex and convoluted. P2 Connector On Power Supply This chapter is from the book  This chapter is from the book CompTIA A+ 220-801 and 220-802 Cert Guide, Deluxe Edition, 3rd Edition Learn More Buy This chapter is from Dell Atx Power Supply Pinout To test an AC outlet with a multimeter, run through the following steps: Place the multimeter's black lead in the outlet's ground. (The parts of the outlet are labeled in Figure

Fortunately, these seem to be the exceptions. Get More Info If you have the means, try swapping out the PSU or testing it in another system to be 100% sure it's not the cause. Also, even if a card physically fits a particular slot, a connector protruding from that card may interfere with another card, or there may not be enough room to route a A higher power iron or small soldering gun will be needed for dealing with larger components. Motherboard Power Switch Connector

Power supplies have a built-in safety feature that shuts down the unit immediately in case of short circuit. Some motherboards use power supplies that feature several additional connectors to supply added power, as follows (see Figure 4-4): The four-wire square ATX12V connector provides additional 12V power to the motherboard; An, example of a simple version of such a device is the "capacitor discharge indicator circuit" described above. (From: Ian Field ([email protected]).) The version of the checker that I have, also useful reference Another live power test for experienced technicians is to bypass the motherboard switching circuit by disconnecting all of the power supply leads to the motherboard and then shorting the green P_On

The total discharge time is approximately 1 second per 100 uF of capacitance (5RC with R = 2 K ohms). A Connector On A Motherboard That Consists Of Pins That Stick Up From The Board Medical students have a saying, "when you hear thundering hooves, don't think about zebras." In other words, most of the time it'll be horses, and you can waste a lot of At times, we've been forced to use only a few screws to secure the motherboard.

Since I can't upgrade the power supply, this is probably the path of least resistance.

Change it to the correct voltage for your location if necessary. IGBTs may be found in large systems and SCRs or triacs are used where their advantages (latching in the on state and high power capability) outweigh the increased complexity of the In that location, it will limit the current to the HOT from the main filter capacitors of line connected power supplies. P9 Connector This odor can linger for weeks.

A visual indication of charge and polarity is provided from maximum input down to a few volts. You can plug fans like this into the three-prong chassis fan connection found on many recent motherboards or into the 4-pin Molex drive power connector used by hard drives. Correct them and retest. this page DC-DC converters are switchmode power supplies without the line input rectification and filtering.

However, you may find other types of circuits in TVs and monitors. It's surprising how easy it is to remove the wrong card if you're not careful. Their secondary high voltage windings were connected together to couple the two transformers together. High quality power supplies ship with PWM (Pulse Width Modulation) fans, which are capable of running at much lower RPMs than fans that are controlled by the voltage level.