Home > How To > Need Help Hooking Up 2nd Hd

Need Help Hooking Up 2nd Hd

Contents

Solved all my problems putting my new S-ATA HDD in under Vista. I was trying to set the 2 HDD on IDE1 (Secondary) as Master and slave, and it wouldn't work. Reply Tyler Thompson on September 10, 2007 at 2:10 pm David,When you clone a drive, it copies it exactly as it were before. Type diskmgmt.msc and enter 3. Check This Out

Comments Add more storage to your PC with a new hard drive In 2011, hard disk prices roughly doubled after factories in Thailand were devastated by flooding. Then there is the BIOS It says A5. Heck, I've even had to go to Wikipedia to understand what SATA is!Great website! Reply bill taylor on September 8, 2008 at 5:01 pm thanks for the help!

How To Install A Second Hard Drive Windows 10

Reply David D on June 3, 2008 at 12:56 pm I'm planning a hard drive replacement. Thanks for the easy to follow instructions. Cheers Ernie Reply Joshcore on July 31, 2007 at 11:04 pm Well done, Ernie 🙂 Reply William on August 3, 2007 at 6:08 pm Hi Joshcore thanks for the advice,I am Step 1: Back up and scout around First, back up your critical files (don't forget your Outlook .PST archive) to optical discs, an external drive, or online storage.

Cheers! I booted from the 80 gig drive. Any later program installations (apart from system-related ones) will be done to the new disk – have a dedicated place/path for that. Second Hard Drive Not Showing SATA drives use a thin, seven-pin data cable; IDE drives use a 40-pin ribbon cable that's usually gray.

jumpers sata Hmmm i hear google works good… NOT to mention on box and back and paper instruction come with drive it clearly points out where and what the Jumpers are. I know you can't add more drives to the raid setup, is that the only difference.Note; I do have 2 other 1tb drives just running as spares and my data back Reply Mark on January 31, 2008 at 2:43 am My old hard drive crashed. See more Why I can't see my IDE HDD and DVD rom on my SATA PC Internal maxtor hard disk not detected in windows 7 2nd drive unrecognised bios Second hard

Reply greg on April 27, 2009 at 9:12 pm I would first try cable select though I cannot verify the results. How To Connect Two Hard Disk In One Pc Add > (load Disk 1 (disk 0 being old hdd and disk 1 being new hdd)) from which you're going to borrow space 5a. I tried what u said to do to change it to auto and everything was already set to auto. A 320GB drive, for instance, formats to about 300GB.

How To Install A Second Hard Drive Windows 7

I want to be able to move back and forth between my Win7 and Win8 boot disks, and use the same data, on a third disk - using the same name Yes No Cookies make wikiHow better. How To Install A Second Hard Drive Windows 10 This is because, for an IDE drive, it matters. How To Connect Two Sata Hard Disk In One Pc When I insert the CD on the drive I am getting a dialog box that I require 256MB memory.

Reply James Bruce September 12, 2016 at 7:40 am Chances are you have some other power cable, like an ATX one. Previous Post5 Cool DIY Ways To Keep Your Laptop CoolNext PostHow To Install A New Hard Drive To Replace An Old One 45 comments Write a Comment nadun flower November 22, You could also change the location of your Program Files, Windows, and other system folders. Do I just set the new drive as slave until I load the image to it and then powerdown and remove the old drive and set the new one to master? How To Install A Second Sata Hard Drive

Reply James Bruce August 1, 2016 at 8:40 am 1. This is VERY time-consuming usually. Changing the location of the folders and moving the files over while Windows is already installed is more complicated. Live in Moscow Russia now.

Double-check all of the connections, boot into the BIOS and check again. How To Configure A Second Hard Drive To confirm that Windows recognizes the drive, open up Device Manager. Risley - it's not easy finding good tech support at 10:30, but I've been waiting too long to get this up new drive up and running to wait, and this little

I created a logical partition with PM which could then be seen by DOS and Windows.

I've hooked up all the cables and turned the drive to "On" in the Setup Utility. Reply Ravenwolfvoyager on September 29, 2007 at 1:14 pm Great article, I really appreciate the simplicity involved and the easy to follow instructions. I toruble shoot circuits for a living and use computers every day for work. How To Connect External Hard Disk To Pc Reply ian on December 26, 2008 at 2:19 am hi, nice step by step, but can you tell me how can i locate the slave hard drive when it is not

They'll have a couple of rubber or plastic blocks covering some pins. With Storage Spaces, you can combine multiple hard drives into a single drive. I only had to format the new drive. It doesn’t matter whether you create a primary, extended or logical partition.

It may have its own BIOS to check. Published 09/20/13 DID YOU KNOW?Granny Smith apples, a popular variety of apples with a bright green coloration and mellow taste (once ripened), are named after Maria Ann "Granny" Smith who first Let’s do this! 1. I knew some of the terms, but it took a few minutes to learn what they were and then followed the clear steps to install, config and run the two drive

https://www.amazon.com/RiteCable-Power-Splitter-Cable-Drive/dp/B01GABJW3I/ https://www.amazon.com/Cable-Matters-Molex-Power-Adapter/dp/B00STNUB04/ Reply Martin Lee October 5, 2016 at 4:58 pm Is it better to let the shop people install it for you? The intent was just a secondary drive for extra space. It is partitioned into 3 partitions and has worked perfectly. Just rock it back and forth (lengthwise along the narrow side of the drive), taking care not to rip the connector off the drive.

Finding the manager and getting it to format so I could see it on my computer was the missing step.