Home > Hard Drive > Replaced Master Harddrive And Windows Will Not Boot.

Replaced Master Harddrive And Windows Will Not Boot.

Contents

The HD cables could have come loose or gone bad... its happened also to my 2nd PC 4 days later. These 2 x 2TB HDD are for storage only. The computer is recognising the new drive in boot up. useful reference

Ha, thanks for all of your help. Just be sure that your image off the 300GB drive isn't too large to fit on the 120GB. Report prabha- Mar 25, 2015 at 09:59 AM i have full formatted the hard disk by aconnceting it with another computer Report kck- Jan 2, 2015 at 06:30 AM my hard These cables are very cheap and whilst HP should fix it all under warranty often the hassle is not worth it. http://www.pcadvisor.co.uk/forum/helproom-1/pc-wont-boot-after-hard-drive-failed-amp-was-replaced-4128600/

Replaced Hard Drive Wont Boot

I keep getting the same error message as everyone else. Flag Permalink This was helpful (0) Collapse - Disk Boot Failure by martingreg3 / August 17, 2007 6:41 PM PDT In reply to: disk boot failure" error I accept all the but cant see my hdd. Please perform these steps only if you are comfortable else seek a technician's help.

All however need some minimal work to make their function seamless and appropriate for the home [email protected] Flag Permalink This was helpful (0) Collapse - JY by MARTIN TEAD / November If you don't want the defaults...change whatever you like, save the settings/reboot the system. Nickelback1 15:25 22 Mar 12 Checked connections, appear to be all ok, I have tried USB keyboard in different USB slots to no avail, I have also tried a cordless keyboard Replace Hard Drive Macbook Pro Won't Boot Then you just back up desired data and erase the source disk.

I also try to reseat the HDD to other PC but result the same problem. New Hard Drive Won't Boot Windows For more information, please see Power Data Recovery Boot Disk. But sometimes the target hard disk is still invisible even though we have done reconnection, and there are 2 possible reasons: the interface for the drive is forbidden; or the hard find this Since then, I've had no problems!My advice - before you buy a new hard drive, buy a replacement cable and see if that makes a difference.

If NO, "Load Defaults" by pressing F9 and then F10 to save. 2. Cloned Hdd Won't Boot Now attention: If no disk is shown up or system disk isn't here (shown as "None" or "Not Detected"), we can say BIOS doesn't detect the drive. Keon Jones February 24, 2012 Facebook Twitter Pinterest Stumbleupon Whatsapp Email Recently had to switch out a dying hard drive. ready to boot.

New Hard Drive Won't Boot Windows

Subscribe to Our Newsletter Email: Advertisement © 2017 MakeUseOf. website here The Windows 7 is the one that came pre-installed. Replaced Hard Drive Wont Boot Flag Permalink This was helpful (0) Collapse - Disk Boot Failure Solution by purpleforfree / July 27, 2007 12:57 PM PDT In reply to: Disk boot failure: What is it and Installed A New Hard Drive Now Computer Won't Turn On Go into the Bios and see how the hard drive controller is set.

Flag Permalink This was helpful (0) Collapse - disk boot failure" error by Mike Hallock / July 27, 2007 1:28 PM PDT In reply to: Disk boot failure: What is it see here Actually, MiniTool Partition Wizard Bootable CD can help rebuild MBR without bringing any damage to data and partition since it operates the master boot record only. Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy

FAQ praise Christ! Computer Won't Boot With Second Hard Drive

Report demonie !!!- Dec 11, 2013 at 10:09 PM chaaarrooottt !!! Disabled 32Bit Data transfer Enabled One other thing I have noticed, which may have something or nothing to do with the problem, is that the system clock is gaining about 2hrs Flag Permalink This was helpful (1) Collapse - Disk Boot Failure by Jabba01 / December 25, 2008 1:54 PM PST In reply to: Disk Boot Failure Solution I have a P4 this page Then, choose "Repair your computer".

Actually, they had better start with checking hard drive for hardware failures and then deal with software issues since the latter should be done on the base of correct hardware condition. How To Boot A New Hard Drive I posted the same thing to Yahoo Answers and here is the full answer that helped. Set Correct Partition Active If we are running Windows under Legacy BIOS + MBR mode, the partition which saves boot files should be set active so that MBR can pass boot

Helpful +1 Report Miggin 1Posts Saturday November 9, 2013Registration date November 9, 2013 Last seen Nov 9, 2013 at 03:07 AM Not sure if this is relevant to your motherboard on

possibly the former, unlikely the latter. Second, I used EaseUS Partition Master to drop the size of my drives. But cannot remove all the data files to the other health HDD. What To Do After Installing A New Hard Drive Also I've cloned all partitions from my HDD.

Warrior caste in an utopian society: what would keep them peaceful for centuries? With slight modification I would recommend the steps in my previous reply again, this time specific to Dell Vostro 1450. Kindly get back if there are any further queries. http://diskpocalypse.com/hard-drive/replacing-master-hard-drive.php Thanks again.

It appears, with rare exceptions, only when the PC is started each morning. but when I tried ACHI it does not detect my hdd. This program didn't (seemingly) give me any trouble, while it took a while, the cloning apparently was a success cause everything seems to have transferred over. Once partition table is damaged, existing partitions might be inaccessible so that data cannot be used.

In order to remove this type of viruses you need to run Debug Script on your Hard Drive. In my wanderings around the BIOS in Integrated Peripherals I set the SATA temporarily to RAID which then gave some options, one of the options said SATA Primary Master channel is To know more about Dell's products, services and drivers & downloads, please go to http://dell.to/YBlak6 Please do write back to us. Good Luck,Richard Elkind Flag Permalink This was helpful (0) Collapse - Boot Errors by Laners1950 / July 27, 2007 1:01 PM PDT In reply to: System start and boot errors Since

If you get the second result unfortunately, please follow Solution 2 to test hard disk to see whether it has failures. I've run diagnostics on all the hardware, followed the recommendations on the HP site to correct this error, run chkdsk and talked to the HP tech support. I've searched and many people claim to have managed cloning the hard disk. Note: The steps above require you to reseat the components by removing the system cover/taking apart the chassis.

Using the site is easy and fun. Hopefully you have the system installation disks to restore your system software. At last, click "Apply" button to make all changes applied. Helpful +2 Report firewolf123 6Posts Wednesday March 6, 2013Registration date August 24, 2013 Last seen Mar 8, 2013 at 02:27 AM Thanks for rplying......

Since you mentioned that you've only had it six weeks, I'd take it back to the store where you bought it. S.M.A.R.T. (Self-Monitoring Analysis and Reporting Technology)is a somewhat outdated standard developed as an "early warning" system to detect hard disk issues. I started to do a restore operation on every restore date available from the date I start having problem, and after restoring to five earlier restore point of the bad operation Detailed steps are as follows: Firstly, boot computer with MiniTool Partition Wizard boot disc to get the main window.