Home > Hard Drive > Need Help With Ide Drives

Need Help With Ide Drives

Contents

You will see some kind of stripe running down the side of the cable that will indicate pin 1. Let's Begin Unpack everything. I've used Syba's IDE/SATA Converter. I didn't want to re-install windows (until vista) and then I might switch things around. navigate here

solved Laptop is not recognizing old IDE HDD connected via USB adapter. The cable length will affect your choice too, as IDE cables are usually quite short. SATA power plugs are by convention black plastic to distinguish them from the white plastic Molex plugs used on the older IDE/PATA drives. Please try again now or at a later time.

How To Connect Ide Hard Drive To Sata Motherboard

Go into the Control Panel -> go under Administrative Tools -> Computer Management -> Storage -> Disk Management. it freezes at the windows loading screen.>i formatted and partitoned the SATA drive wiv the disk writer program from Seagate, and now the SATA switches between being one partition or the EaseUS softwar… Related Products Data Recovery Software Data Backup Software Partition Manager Software PC Transfer Software Mac System Utility File Sync Utility Top 10 Hot Articles Recover Pictures after Factory Reset

by R. There is a sample about Seagate hard drive jumper setting. Before, the cd and dvd drives were e: and f:, the hd(when it was recognized) was still g:Not sure why it happened (I might try removing all emulation drives first and How Many Hard Drives Can Be Connected To A Single Ide Cable Unfortunately some are flimsy or have poor quality control.

Is the full capacity of the hard drive being seen: Verify the BIOS has auto-detected and LBA mode is enabled. Sata And Ide Hard Drives Together If you have trouble removing the "blank" you can use a flat ended screwdriver to ease it out, taking care not to damage the case. The example I/O controller card below gives you one SATA socket, one PATA socket, and one eSATA (external SATA) socket. Flag Permalink This was helpful (0) Collapse - Mixing SATA and IDE drives in a system?

Selection is done by means of a jumper, the option you choose will depend on any other IDE devices you have installed and their respective settings. Ide And Sata Drives In Same Computer Further, some IDE cables have a blank in one hole to stop you inserting it incorrectly. I just switched the cables, put my dvd and cd writer drives on the primary IDE cable instead, restarted, and voila!My drive lettering is messed up nowA:floppy C:SATA HD ------ ok Please refer to our CNET Forums policies for details.

Sata And Ide Hard Drives Together

I have an 80gb IDE and want to add more memory. The hard disk is similar, but this time I chose “Master with Slave Present“. How To Connect Ide Hard Drive To Sata Motherboard After boot windows xp/operating system on HD SATA, i re-activate IDE HDs and after backup data, repartitioned like i want. 5. Ide Hard Drive Jumper Settings When you first start your machine enter into the BIOS and make sure the drive was identified properly.

SATA advantages over the older PATA specs include faster data transfer, higher efficiency, hot plugging, reduced cable width, and better internal air flow. http://diskpocalypse.com/hard-drive/recommended-hard-drives.php You'll see some kind of diagram that looks like this: It's not currently set, but you can fairly easily tell from the diagram what you'll need to set it for. If you want to make it the master or the slave, you will have to look around the drive to find where the instructions are. IDE includes sub-standards with names like EIDE, ATAPI, ATA, ATA-1, ATA-2, UDMA, ATA-4, ATA-133, and more. How To Connect Ide Dvd Drive To Sata Motherboard

Flag Permalink This was helpful (0) Collapse - Feel free to make a new post. Just clicking next until you get here. Can a USB SATA Hard Drive enclosure be converted to IDE? his comment is here SHOW ME NOW CNET © CBS Interactive Inc.  /  All Rights Reserved.

Flag Permalink This was helpful (2) Collapse - Should not be a problem by xpostal / July 22, 2005 1:49 AM PDT In reply to: Mixing SATA and IDE drives in Ide To Sata Connector Prior settings of the jumpers to "slave" would result in no boot screen at all upon powering on. Most IDE disk drives use an IDE data ribbon connector and a white power plug, while most SATA drives use the SATA data cable connector and a black power plug.

Smalltalk was the first programming language to have a first true IDE.

The article is correct. Flag Permalink This was helpful (0) Collapse - also sata ide troubles by babs123456 / November 14, 2006 1:30 AM PST In reply to: mixing of sata and ide i too On even older mainboards you'll find a 32 GB limit. Motherboard With Ide And Sata Ports Previous PostHow To Install A New Hard Drive To Replace An Old OneNext Post3 DIY Computer Repairs You Can Easily Do Yourself 10 comments Write a Comment Chris Balfoort August 31,

Transition Drive Uses Either Power Plug  (Gateway) Inspect your motherboard, too. What are jumpers? They should have some instructions posted. http://diskpocalypse.com/hard-drive/refurbished-hard-drives.php This will enable a sufficient amount of air to flow between the two drives.

Ask a new question Read More Hard Drives Laptops USB Storage Product Related Resources How to connect laptop-style slim DVD drive to IDE or USB p.. My hard drive doesn't have the jumper settings on the label: Find the model number and visit the manufacturers website. OSNews and the OSNews logo are trademarks of OSNews. Customer Login Reseller Login EaseUS Solution Free Data Recovery Software Free Backup Software Free Partition Manager Discover EaseUS Company Partner Contact us User Guide Data Recovery Wizard Todo Backup Partition Master

Then you connect its special power plug that powers both the connector and drive. What is IDE ? After the drive is secured then go ahead and connect the power and IDE cables. also i've updated the bios drivers and according to other forums should have stopped the Sata troubles.>ive tried setting the IDE to primary slave and cable select but none have changed

This article discusses the options. The case screws are bigger than the ones used to screw in your CD drives. There are two things to keep in mind, do not overload your power supply or strange difficult problems will begin to occur and make the correct BIOS settings for your data Flag Permalink This was helpful (1) Collapse - It's all about the controllers by DJPython / July 22, 2005 5:53 AM PDT In reply to: Mixing SATA and IDE drives in

Set The Jumpers & Plug In Since I only have a single IDE CD-ROM and single hard disk to show you today (as well as only a single physical IDE connector I've been trying to resurrect an old wheel alignment system for the shop I work at. by R. Be sure to follow any instructions about the jumpers on the IDE drives.

OSNews Forgot Password · Register Login to OSNews Username or EmailPassword Search OSNews Advanced Search Submit News RSS Home Originals News Archive Shopping Topics FAQs Contact Advertise How to Integrate SATA A couple of things to consider though: 1.